Node-RED-style visual flow programming for microcontrollers
ThingStudio is a free, open-source visual flow programming environment for microcontrollers, inspired by Node-RED. You build flows in a browser-based editor on your own computer; it compiles them to MicroPython (and .mpy bytecode) and deploys them over USB or WiFi to boards running ESP32, RP2040/RP2350, nRF52840, or STM32 chips. The flow is saved on the board itself, so it keeps running with the editor closed and survives power cycles. Development is fully local — no cloud, no account, no telemetry — and everything is editable and hackable.
Pick nodes from a palette and wire them together; messages travel along wires in msg['payload'], just like Node-RED.
The editor compiles your flow to MicroPython, then to .mpy bytecode, and sends it over USB or WiFi. The flow is saved on the board and keeps running after you close the editor, unplug, reset, or power cycle.
Instead of one ever-growing main loop, each node runs only when its event fires — interrupts, debounced buttons, rotary encoders, analog inputs crossing bounds — and the board waits on many events at once.
Board definition files list pins, LEDs, reserved pins, and SPI/I2C bus options. The compile checks every pin against the target board and stops with an explanation if a pin doesn't exist, would crash the board, or conflicts between nodes.
Built-in nodes cover pins, buttons, switches, encoders, ADC, PWM, Neopixels, sensors (BME280), MQTT, HTTP, UDP, NTP, WiFi status, timers, plus debug, journal, filter, and change nodes.
Write your own function nodes in MicroPython or package custom nodes with their own palette entries; add new boards and processors by dropping JSON files into a folder.
No cloud service and no account; the editor sends nothing home. Once installed it works offline, docs included.
Programs and board definitions are plain, indented JSON that diffs cleanly. Credentials are stored separately so committed programs hold no secrets.
The editor runs in your browser on your own computer (you can also try it in the browser with nothing to install). You pick nodes, draw wires, and configure pins.
The editor compiles the flow to MicroPython source, then to .mpy bytecode.
The compiled flow is sent to the board. A change is a new deploy, not a firmware build, and takes seconds. The flow is saved on the board and restarts after reset or power cycle.
Write MicroPython in function nodes, create custom nodes for the palette, and add board/processor definition files by dropping them into a folder — nothing to rebuild.
Free and open source under the Apache 2.0 licence.
A visual flow programming environment for microcontrollers running MicroPython, inspired by Node-RED. You build flows in a browser editor on your computer, and ThingStudio compiles them to MicroPython to run on the board itself.
It works with boards running MicroPython on ESP32 (including S2, S3, C3, and C5 variants), RP2040 and RP2350 (Raspberry Pi Pico family), nRF52840, and STM32F405. Tested boards include Wemos D1 R32, the CYD, LOLIN S2 Mini, Freenove ESP32-S3 Display, Pico, Pico W, Pico 2, Seeed XIAO nRF52840, and Pyboard v1.0.
Yes. The compiled flow is saved on the board. It keeps running when the editor is closed or the cable is unplugged, and restarts after a reset or power cycle.
In Node-RED the editor and runtime are one program on one computer. ThingStudio splits them: you build the flow on your computer, it compiles to MicroPython, and the flow runs on the microcontroller itself. Its native language is MicroPython and it runs on bare metal.
It's free and open source under the Apache 2.0 licence, so you can use, change, and build on it, including in commercial products.
No. Development happens entirely on your computer with no cloud service and no account. Once installed it works offline, docs included, and the editor sends nothing home.
Yes. You can write custom nodes with their own palette entries, and add your own board and processor definitions by dropping JSON files into a folder — nothing needs rebuilding.
No. It's aimed at people who can already program and have used a microcontroller. You should be comfortable wiring a breadboard and typing commands in a terminal.